angle of shear的例句大全

However, at higher angle of tooth-shaped asperities and under higher normal stress, the failure model II is found, which is in first tension but final shear failure.

在较高的法向应力下，含起伏角较高齿形节理面的非贯通节理岩体可能出现破坏模式II（先张拉后剪切破坏模式）。

互联网摘选

An analysis of size effect of the inclination angle of shear band and the onset, skip and stability of shear strain localization

剪切带倾角尺度律与局部化启动跳跃稳定研究

互联网摘选

The shear stress concentrates in the retaining substructure and the angle of slope, especially serious in the angle of slope.

剪应力在支护结构和坡角处有集中现象，在坡角处较为严重。

互联网摘选

And the formula for angle of shear plane is modified by chip shortening coefficient.

并通过切屑变形系数来修正模型中的剪切角计算公式。

互联网摘选

Statistics Analysis on Friction Angle of Shear Strength for Clay

粘土抗剪强度内摩擦角统计分析

互联网摘选

Larger inclination angle of shear band is caused by larger rigidity of platen.

压头刚性越大，剪切带倾角增加，试件脆性增强。

互联网摘选

Larger loading rate leads to larger inclination angle of shear band in the middle of specimen.

随着加载速率的增加，岩石中部剪切带的倾角有增大的趋势。

互联网摘选

Bigger inclination angle of shear band leads to bigger dissipated energy of lateral plastic deformation and smaller dissipated energy of lateral plastic deformation.

增加剪切带倾角，侧向塑性变形消耗的能量占剪切带消耗的能量的比例增加。

互联网摘选

The increase of the inclination angle of shear band and its width has an opposite influence on stress-strain curve of specimen after localization occurs.

剪切带倾角和宽度的增加对岩样的塑性性质影响正相反。

互联网摘选

Dissipated energy due to axial plastic deformation is proportional to that of lateral plastic deformation and the proportional coefficient is dependent on inclination angle of shear band.

轴向塑性变形消耗的能量与侧向塑性变形消耗的能量成正比，其比例系数与剪切带倾角有关；

互联网摘选

Based on the limit equilibrium theory and the hypothesis of planar sliding surface, a formula for calculating the angle of shear failure was deduced considering cohesion and cut slope angle.

基于极限平衡理论及平面滑裂面假定，在考虑土黏聚力及放坡角度的基础上，推导了平面滑裂面剪切破坏角的数学表达式。

互联网摘选

The effect of transverse shear deformation is considered and angle of rotation of surface normal for each layer is different.

这类板的横向剪切变形效应必须予以考虑，因而层板不同层的表面法线的转角是不同的。

互联网摘选

By integrating the function, the shear force, bending moment and the angle of rotation of the whole beam are expressed by one equation respectively.

通过积分，全梁的剪力、弯矩、转角和挠度可分别用一个方程表示。

互联网摘选

The results of the tests show that with compaction water content increasing, the compression deformation increases, the shear strength decreases and angle of friction also decreases.

试验表明：随压实含水量增大，粘土的压缩变形增加、抗剪强度降低；

互联网摘选

Results show that degree of compaction, compaction water content and saturation state of compacted soil have influence on cohesion and angle of friction of clay, thereby on the shear strength of clay.

试验表明，压实度、压实含水量及土体饱和状态对粘聚力和内摩擦角有影响，从而使抗剪强度也受到三因素的影响。

互联网摘选

To cope with the demand for a control system dictated by angle bar shearing shop practice, a new dc on-off control system governing the operation of the flying shear in a logic manner is developed.

作者根据起停式角钢飞剪的剪切工艺要求，研制出一种新型的起停式飞剪的直流控制系统。

互联网摘选

The velocity distributing, variation of extension rate, shear rate and the natural convergence angle of the fluid were analyzed under different initial entry pressure.

分析了在不同口模压力（P）下入口区速度分布、延伸应变速率、剪切应变速率以及流体自然收敛角的变化。

互联网摘选

Through the checking calculation and adjusting of the parameter of the shear wall using the deformation aim gained from the inelastic displacement spectra method and the fitted drift angle evaluation function of deferent performance level, the performance level of the shear wall could he realized.

根据弹塑性位移反应谱法得到的目标位移和本文拟合的剪力墙构件各性能状态位移角估算公式进行验算、调整，可以实现剪力墙结构不同的性态目标。

互联网摘选

New Methods on the Determination of Martensitic Transformation Shear Angle and Lattice Parameters;

马氏体相变切变角和点阵常数测定的新方法◆剪切角可调，减少板料扭曲变形。

互联网摘选

The mechanisms of semi-periodic variation of chip thickness were discussed, and combining with shear angle changing and dynamic behaviour of microcracks, models of chip forming process were established for SiC_p/ Al composites with different reinforcement volume fraction. 2.

探讨了切屑厚度准周期变化的内在机制，将剪切角周期变化和微裂纹的动态影响相结合，建立了适应含不同颗粒体分比的该材料的切屑形成过程模型。

互联网摘选