bending modulus的例句大全

With respect of bamboo, bending strength and modulus of rupture increased gradually from inboard bamboo inner place to outboard bamboo skin in the radial direction.

毛竹沿径向的弯曲强度和弯曲模量从最内层竹黄处向最外层竹青处逐渐增大。

互联网摘选

Investigation of influence factors on bending modulus of carbon fiber/? Epoxy

碳纤维/环氧复合材料弯曲模量影响因素的研究

互联网摘选

Adding GF increased not only tensile strength and bending modulus but also impact strength of the composite.

GF的加入不但提高了材料拉伸强度、弯曲性能，而且提高了其冲击强度；

互联网摘选

The tensile strength and the bending modulus of RHDPE/ EVA/ MWRP blend increased by 35% and 25% respectively when the waste rubber powder was modified by self-made surface modifier ACDI.

废胶粉经自制表面改性剂ACDI预处理后，其相应的RHDPE/EVA/MWRP体系的拉伸强度和弯曲模量分别增加35%和25%，而对共混物的其它性能影响不大。

互联网摘选

For uniform isotropic materials, bending modulus of three point bending ( TPB) test and four point bending ( FPB) test are almost the same and they are almost equal to material ′ s tensile modulus.

对于均质各向同性材料，三点弯曲实验和四点弯曲实验得到的弯曲模量与拉伸模量基本上一致。

互联网摘选

The experiment shows that the retention of extension strength, bending strength and their modulus are above 60% below the 250 ℃, which has super high loading capacity.

实验表明，在250℃下其拉伸和弯曲强度及模量的保留率均在60%以上，仍具有极高的承载能力。

互联网摘选

Analysis of Equivalent Elastic Modulus of Single-Walled Carbon Nanotube Under Bending and Tensile Load

碳纳米管弯曲和拉伸等效弹性模量的计算分析

互联网摘选

The results indicated that for GB/ PP composites, with the increase of the GB content, the tensile modulus, bending strength and modulus increased linearly, while the yield strength decreased slightly;

结果表明：随着GB用量的增加，单、双螺杆挤出GB/PP复合材料的拉伸模量、弯曲强度和弯曲模量均呈线性增长的趋势，而屈服强度则有小幅下降；

互联网摘选

Through math analysis of math model, it could get the smaller of overfeeding sewing shrinkage when the fabric bending – tensile modulus ratio and the fabric connection length ratio were bigger, and the connection length was smaller.

通过对数学模型的数字解析可知：面料弯拉模量比越大、面料连接长度比越大、面料连接长度越小，超喂缝缩率越小。

互联网摘选

For GB/ LLDPE composites extruded by single screw extruder, with the increase of filler content, the tensile modulus, bending modulus increased linearly, while the yield strength and bending strength increased slightly at higher filler content.

而GB/LLDPE中，随着GB用量的增加，单螺杆挤出复合材料的拉伸模量、弯曲模量均呈线性增长趋势，而屈服强度和弯曲强度在含量较高时略有上升；

互联网摘选

The results showed that the notched Izod impact strength and conservation rate of tensile yield stress of HDPE E-TMB were markedly superior to those of HDPE elastomer, while the conservation rate of elastic modulus in bending of HDPE E-TMB and HDPE elastomer was nearly the same.

结果表明，HDPE/ETMB的悬臂梁缺口冲击强度的提高幅度、拉伸屈服应力保持率均显著优于HDPE/弹性体，二者的弯曲弹性模量保持率基本相同；

互联网摘选

As result of tension strength and tangential Modulus of rupture ( MOR) are very small, it indicates that the properties of tension and bending are very bad.

而横纹拉伸强度值和弯曲强度值均较小，说明杨木单板的横纹抗拉、抗弯性能差。

互联网摘选

Effects of temperature and loading rate on the flexural-tensile strength, strain and stiffness modulus of ATB-25 asphalt mixture were discussed using three-point bending test.

通过沥青稳定碎石基层ATB-25沥青混合料的三点弯曲试验，研究了温度及加载速率对弯拉强度、弯拉应变及弯曲劲度模量的影响规律。

互联网摘选

Methods Flexural strength and elastic modulus were measured by three-point bending test at selected temperatures from 830 C to 950. X-ray diffraction was used to investigate the type of crystal and crystal percentage.

方法按不同晶化温度条件分组，利用X射线衍射技术鉴定晶相，计算晶体含量，并采用三点弯曲法测定各组的抗弯强度和弹性模量。

互联网摘选

Its producing area, exposed to the sun and measurement mode had a marked effect on bending strength, but affected modulus of rupture indistinctively.

毛竹的产地、生长朝向和测量方式均对弯曲强度影响较大而对弯曲模量影响则较小。

互联网摘选

Influence of modulus of elasticity on the forming precision of lapping tools in the aspherical lapping of bending formation method;

结果表明，晶体取向对合金枝晶组织形态和偏析存在显著影响，而合金的弹性模量和持久性能也存在明显的各向异性。

互联网摘选

Method for determination of the modulus of elasticity in static bending of wood

GB/T1936.2-1991木材抗弯弹性模量测定方法

互联网摘选

The dynamic modulus of elasticity ( MOE) in bending of plywood was measured by tests of flexural vibration, longitudinal transmission and longitudinal resonant vibration.

通过弯曲振动试验、纵波传播试验及纵波共振试验对胶合板的抗弯弹性模量进行无损检测，并分析了三种试验方法测定结果之间的关系。

互联网摘选

Expounded punching, blanking, bending modulus of the composite structure design and principle.

阐述了冲孔 、 落料 、 压弯复合模的结构设计及工作原理.

互联网摘选

The relationship between bending modulus of elasticity and bending strength was also linear.

抗弯弹性模量与抗弯强度具有密切的线性关系.

互联网摘选